DIY Spiderlight.... SOFTBOX !

Last week I posted a DIY article on building a DIY Spiderlight. If you haven't seen it here it is:


I finally had some time to complete the softbox that was meant to go along this light fixture.
Here's what it looks like (without the diffuser panel):


I am so happy. The whole thing is very lightweight and also really strong. It also costs a fraction of a real softbox. Be advised though, this won't be done in an hour. It took me several hours to build it, and it is mostly because of the curved shape of the 4 sides. A "pyramidal" shaped softbox would have been much less complicated. But hey... does it look cool or what !

To build this baby you will need:
- a 4' x 8' sheet of black corrugated plastic. Also called Coroplast (about 20$ and you can get it at your local signmaker or hardware store).
- a roll of STRONG aluminum foil
- Spray adhesive
- Aluminum tape
- Some wood to make the frame
- Some material for the diffuser panel. I bought a piece of ripstop nylon. Seems to work fine and it is also the "standard" material for this purpose.
- a couple of "L" shaped metal brackets
- Tools: Knife, scissors, T-50 stapler + staples

That's pretty much it! About 35$ total for everything.
Here's how it was done:


Here's is a piece of coroplast with the layout of one of the big side parts.


One of the sides cut out. Notice the direction of the channels on this piece. This is important ! (No, I did NOT cut this on the hardwood floor!)


Here's a template for cutting the sides. Click for full size jpg.



Cutout of one of the top/bottom panels. Notice the direction of the channels on this piece. This is important !


When you bend coroplast in the wrong direction, it can be desastrous. To avoid permanent fold marks, simply take a very sharp knife and cut the FIRST HALF the the coroplast layer. I did a cut every inches or so. This allows the whole panel to bend nicely without any problem (at least not yet...more details coming).


Aluminum foil applied to the panel with spray adhesive.
***** UPDATE May 1st 2008 *****
It has been brought to my attention that Mylar (the stuff heat survival blanket are made of) could do a much better job of reflecting that precious light. A good thing to know. I will probably replace the alu foil with some of this mylar soon...


Here's the wood frame what will hold everything together. It will also be used to hold the diffusion panel as well. I did not picture any steps regarding the construction of this frame since the excellent strobist, do-it-yourselfer and photographer Nick Wheeleroz already did it when he build his own softbox. Click here to read his tutorial on building the wood frame. While you're there, take a couple minutes to check his incredible work too!
By the way Nick, I am a professionnal woodworker myself and i built it exactly the same way as you did. See, no need to go with fancy joinery on that thing :o)
The only difference with his version and mine is that I built it a bit thicker and added a additionnal screw from the side for increased stability.


Here's the part where I TOTALLY SUCKED at this project. The fact that I had cut the first layer of the coroplast to make it bend easier, also made it really soft. I had to temporarily attach both of the softbox sides to the Spiderlight fixture and figure out a crude way to support and secure the whole thing while installing the top and bottom panels. The side panels were first stapled on the wood frame.

I did not know what the final shape of the top/bottom panels would be so I had to take a big piece of thin cartboard and lay it down over the two installed sides and trace it out. I then transferred the layout on the coroplast panels.
Maybe I am making this sound simple but in fact it took me two whole afternoons of head scratching to figure out a way to do it all. Hopefully one of you guys will figure out a better way to do it and post it on this thread.

Oh and I forgot, the top/bottom panels were first stapled to the wood frame. Then, they were connected to the side panels using black duct tape. I know, it ain't pretty, but is holds damn well. At least it's not grey!


The completed softbox. Ain't it pretty ?


A quick look from the inside.


Lightbulbs in. Ready... set....


Yeouch! My eyes! :o)


I placed the diffusion panel (cotton sheet) over the softbox for testing purposes. Both of these shots were taken at 1/200 f2.8 ISO 80. The first one is with all 5 bulbs turned on. The second one is with only 3 of the bulbs turned on (see my tutorial on the DIY-Spiderlight for more details). You can really see the difference in brightness.


Taken at 1/1600 f2.8 ISO 80

Now a first field test (BEWARE OF THE MONSTER):

Yep. It's me. Turned off all other lights in the room and set my camera on the tripod. This shot is not really good. Here's why:
1- I was alone. I had to pre-focus on... thin air. No subject to focus on since i'm behind the camera while composing the shot. That's why it ain't sharp.
2- The softbox is still on the floor. I haven't got my lightstand and swivel bracket yet.
3- The subject is ugly!
4- Again I was alone so no one or/and no lightstand yet to hold a reflector for me.

Anyway. It does work! This was shot at 1/30 f2.8 ISO 80 (please note I shot this using a Powershot S5 IS. The f2.8 on my camera is much more slower than the real f2.8 you are getting on a DSLR lens.). Still a bit too overexposed on the lightened side. Of course this kind of light is not to be used to picture an excited child moving around.

That's pretty much it! Later this week i will install the diffusion panel with velcro on the wood frame. I will also work out a way to make the spiderlight removable with some sort of washers and wing nuts...
As soon as I have my lightstand I will do some more serious testing with hopefully better subjects than me.
Might take a while though... I want to order my first "off-camera" flash. But then I have to decide between Nikon or Canon, but then I have to decide of my next camera as well... and so as lenses and BLAAAHHHHH!!!!!

Anyway. Just give me a couple weeks. I'll be updating this thread as soon as everything is in.

Hope you like the softbox!

Here's some more test shots:

1/60 f2.8 ISO100, No diffusion screen, Softbox on left, DIY reflector on right


1/40 f2.8 ISO100 No diffusion screen, Softbox on left, DIY reflector on right


1/40 f2.8 ISO100 WITH cotton diffusion screen, Softbox on left, DIY reflector on right. Again,please note I shot this using a Powershot S5 IS. The f2.8 on my camera is much more slower than the real f2.8 you are getting on a DSLR lens.


Next chapter: Mounting the whole kit on a light stand!

Alone in the fog....

Well this is literally how it was on that night. Me, totally alone in a park, surrounded by a nice fog. I took a lot of shots, but this one turned out to be the best. More to come later....

DIY Spiderlight Strobe!

It's been a while since I wanted to buy myself a Westcott Spiderlite TD5. As you may know, its pretty darn expensive... about 365$ for the fixture itself without the bulbs. The bulbs will make it an additionnal 100$. That's roughly 465$.
So since I am pretty good at building things (i am a self-employed woodworker) I decided to build my own version of a Spiderlight:


The total cost, for all the materials AND the bulbs is about 120$. That's about 350$ savings! Not bad.

So here's how I did it:


I started with some pieces of half inch MDF I had lying around. I glued 3 layers together to get about 1-1/2" of total thickness. The dimensions are 6-1/2" x 6-1/2". I then I took my 1-1/2" Forstner bit and drilled 5 holes. One in the center and 4 at the corners.



I bought 5 of these rubber bulb sockets. They're fairly inexpensive, running at $2.50 each.


The 1-1/2" holes makes for a perfect, snug fit for these rubber sockets.


The next step is to add some aluminum foil to the bulb side. To get a more diffused effect I wrinkled the foil and then flattened it with an iron. I used spray adhesive to glue the foil to the MDF. I then removed any excess foil around the perimeter.



Here's what it looks like with all 5 sockets installed.



Viewed from the back.



A generous amount of construction adhesive to hold everything in place.



Now the fun part: electrical wiring! I bought this simple little wire switch to turn the whole thing on or off. Don't ask me what gauge the wire is, I just picked up the one that seemed the right choice. It has 3 wires inside. White, black, and green for grounding.



I bought a 4x4 metal box (normally used for laundry dryers) along with the cover plate. I also bought a 2 position "toggle switch" (seen here attached to the cover plate) that will allow me to turn off 2 of the 5 lights to get a little less illumination should the need presents itself. I drilled holes in the inside corners of the metal box to get the socket wires through. Then I screwed the box to the MDF. For liability issues I will not tell you how to wire this. Please note that I TAKE NO RESPONSIBILITIES IF PROBLEMS/FIRES/INJURIES RESULT FROM THE USE OF THIS TUTORIAL.



Here you can see the cover plate attached and the toggle switch in place.



The finished product! Seen here with the wire, switch and wall plug.
The fluorescent bulbs are Phillips Marathon, 27Watt. The color temperature is 5000K, which is the closest to the full-spectrum sunlight I could find at the hardware store (I bought these in a Home Depot in canada). They came in pack of two for around 13$.
***** UPDATE May 1st 2008 *****
If you think that those 5 27W bulbs might not be powerful enough for you, you can replace the 27w's with 4 85W, 5000K General Brand bulbs (available at B&H). That would throw some SERIOUS light!



Taken with the exact same camera settings (except F3.2 instead of 2.7.. .go figure) as the previous shot. All 5 bulbs turned on. Yep, its bright.



Taken at 1/1600 sec. at F3.5.


Same settings, with two of the bulbs turned off using the toggle switch on the back.



Final Product.

Well I can say I am pretty happy with the results. The whole thing weights about two and a half pounds, making it light enought to put on any lightstand.

Come back later this week, as I will post another how-to article on building my 3'x4' softbox to go with the fixture. That one shouldn't cost more than 25$ if everything goes as planned.

The other thing i'll need to do is add some soft of attachment to fit on a lightstand swivel bracket. I might buy the one from Westcott. I will also buy my first lightstand later on.

Hope you liked the tutorial!

Next chapter: Building the Softbox !

Welcome!

Welcome to my Blog everyone. This is my first post ever so please bare with me here. This blog will mostly be about my photographic work, altough i might slide in some of my woodworking stuff too.

Happy blogging!